From fleece fabric or wadding One rectangle, 4cm larger all round than the letter. Fat Quarters are quarter-yard cuts of fabric cut wide hence the name fat. Step 5: Embellish letters with ribbon. Trim off the surplus fabric across each corner, cutting to within 3mm of the card and snip into the margins along any curves and inside angles.
I still am. Tip: A base layer creative writing written explanation fleece fabric wadding gives a softly padded look to the finished letter. The glue works fast, so work in small sections. Cut a 4cm strip, the same depth as the letter and fix it across the corner with double-sided tape.
Leave me a comment with your email address!
Doing this is as I understand it sort of like making bias tape. Clip off the surplus fleece letters covered in fabric each corner, snipping to within 3mm of the letter and cutting at a 45 degree angle. So all I had to do was cut strips from each side of the piece of fabric and I used that as the finished edge.
Finally, fold one end over, so when it's exposed, the raw edges will be covered up and tidy. Want to know how to make your own easy DIY fabric letters? I hot glued the fabric over the batting cover letter for job without relevant experience pulled it to make it fairly tight.
Position the staples close together. I feel I must warn you before I continue with this tutorial. After glueing the L together twice, then the ampersand falling and shattering in a hundred pieces, I gave up.
But I promise, by the last letter depending on how long the name or word you are trying to spell out is you will be a pro! I started with some high quality kraft letters. Trim the margin to 3cm all round. I almost gave up at that point. Once I figured that out I really began to fly on these letters.
I absolutely adore the fabric covered letters at Anthropologiebut I don't want to cough up that kind of cash, plus not sure they have an ampersand anyway.
Now that you've cut the pieces, you'll use the iron and lots of steam to make good closing lines for presentations look like bias tape. Make your "circumference" cover … this is a long strip of fabric that covers the sides of the letters and makes it look very nice and neat!
Turning back the margins Step three: putting on the Liberty fabric Starting at the centre of a long edge and working outwards towards the corners, gently pull the edge of the fleece on to the tape and press it down.
One rectangle, 2cm larger all round than the letter, for the back. I even bought the letters clear back in December…and they have been sitting on the shelf in my craft closet since then. If you are making lots of them, do it all at once!
No one will see the backs of your letters so there is no need to stress over this step.
Cut out a piece of batting that is large enough to cover the front and sides of the letter…. It was just enough to give the letters a little depth, but not too thick to make it hard to work with. I use a sharpie for this step and marked right onto the batting.
The deeper the curve, the more clips you should make. Or a grown-up room as a monogram?
Covering the letter with fabric Step four: Pleating the fabric Place the letter, face down, centrally on to the fabric rectangle. Dealing with inside angles Step seven: inside corners You will need to add an extra layer of fabric at each inside angle, or the letter will peep through the cover.
I got the BIG bag of glue sticks at Walmart for about 2 bucks. Letters covered in fabric the flexible tape measure to find out the "circumference" of the letter exteriors Step 3: Cut out traced area and cut slits in fabric around letter.
If your fabric is wrinkly, iron it! Note how I cut the corners to overlap. I know, I'm not proud. If the batting overlaps the sides of the letter, you will want to trim that down. For the front of your letter, turn the quilted side down so that it's touching the wrong side of the fabric.
Trace letters for Batting. Are you running full sail mfa creative writing cost of glue sticks yet??? Then I sprayed each letter with adhesive on the front and glued on the fabric. I painstakingly painted and antiqued them and mounted them on the door.
Trim the fabric so that there is a 15mm margin all round the edges of the letter. Fold over the margin along the next side of the letter and carry on stapling down. Continue Reading I saw a picture of fabric-covered letters on Pinterest one day and thought that would be fun.
Since they are kraft letters and therefore very lightweight compared to effects of branding dissertation or metal, they seem over the crib appropriate in Southern California where apparently earthquakes do happen.
Going round curves Step five: snipping the fabric To cover an outside curve, pleat the fabric slightly creative writing copywriting pull it towards the centre of the letter. Now glue the excess fabric to the back of the letter, much like we did with the batting in the beginning, including trimming the excess fabric off the outer corners.
They can be matching, or contrasting. You will need two squares for each letter. Flip the letter over and see how it looks. Once again, snipping the fabric at the corners helps in wrapping it around the letters.
But you should get a smooth edge. And you'll get carded at Joann's for buying this.
PS: I will not lie. I cut pieces of the batting, being sure to leave plenty of excess around the letters. Making the back Step nine; finishing off Stick lengths of double-sided tape along each edge of the card letter. Pinky swear.
Preparing the cardboard backing Step one: covering your Liberty print letter Draw around the letter on to the card and cut out around the outline. Your letter should now look like this. Continue Reading Then you are going to need some sort of batting if you want your letters to have a little puffiness to them.
Any questions? Cut in almost but not quite all the way to the edge of the letter.
Turn the corner back at an angle, stretching it gently to get a neat edge, and staple down the point. A word of advice here. Make sense?